** After purchase, please check the battery and charge the battery before use.
** Please refer to the FAQ section on the Aurender homepage for any information you do not find here.
- The Aurender FLOW is a portable High Fidelity Headphone Amp.
- Capable of playing up to 32bit/384KHz PCM and DSD128 (DoP).
-The USB2.0 and USB3.0 ports enable fast data transfers. In addition to video, audio, image files, the FLOW can also be used to store business files, presentations, back-up and other data.
-Can be used as a storage device with desktop PCs, laptops, notebooks and is compatible with a variety of OS systems.
-You can play music stored in FLOW's mSATA driver from PC or Mac
* You need to format the mSATA disk after you install. Please refer to the OS (Windows, Mac) manual for formatting mSATA. The procedure is the same as formatting HDDs.
Control buttons are located on the side of the case, as shown below.
① Move Down Button
1. To go to the next song when playing music
2. To change the menu item when in Menu mode
Many PC/Mac music player program follows the HID standard so you can use FLOW's control button to control the music you play.
② Play/Pause Button
Play/Pause the song you play.
③ Move Up Button
1. To go to the previous song when playing music
2. change the menu item when in Menu mode
④ Menu Button
You can change the settings by pressing the Menu button
⑤ Power button
Press & hold the button for about 2 seconds. The FLOW will power up.
It will show the current Host mode for a few seconds.
* FLOW will automatically turn off if it's not used for about 15 seconds.
Basic Menu - single click
Every click of the Menu button will cycle through the next mode of menu.
% : Battery Percentage
First click will show the percentage of battery power remaining.
Host Mode - Next Click of Menu button shows the Host mode.
* USB cable to the FLOW shoud be removed to change the setting below.
Please set the mode when used with PC with the USB2.0 ports
Please set the mode when used with the PC with the USB2.0.
When FLOW is connected to PC with USB 3.0 port and the mode is set to USB3, the copy speed and charge speed becomes faster than USB2.0 mode. You need a USB3.0 cable to fully utilize the speed of USB3.0.
When FLOW is connected to the Mac, please set the host mode to Mac. The charging speed will be faster than in other modes.
Due to the change of Apple's policies after the version of iOS9.2 FLOW V1000 would not operate normally. Officially the iOS devices will not be supported by FLOW V1000.
For some Android devices with its various version of software, FLOW V1000 could not operate normally. Officially the Android devices will not be supported by FLOW V1000.
Next click shows the Charging mode
CHG+ : Always charge
CHG- : Always no charge
CHGA- : Charge Automatic. (Charge only when not playing music)
mST : Next click shows the status of mSATA drive installed.
mST- : mSATA not installed
mST+ : mSATA installed
* You can set mSATA to not being used even though mSATA drive is installed. To do this, you can change to MST - by using the direction button.
To decide the input priority when both optical cable and USB cable are attached.
OPT+ : Set input to optical
OPT- : Set input to USB
Shows the brightness setting of LCD back light.
* You can change the brightness by pressing directional button.
There are four steps from DIM0 to DIM3.
Shows the version number of the current firmware.
*This is for internal use only.
Advanced Menu - Click & Hold (long-press)
PCM filter options for use when playing PCM files.
pcm0 : Fast roll-off PCM Filter (default setting).
pcm1 : The Slow roll-off PCM Filter is an in-band filter and the output signal will be slightly attenuated.
pcm2 : Minimum phase PCM Filter (virtually eliminates ringing from signals).
For DSD files, the cut-off frequency of the noise-shaping filter may be changed as below.
dsd0 : BW=47.7 kHz in DSD
dsd1 : BW=50 kHz in DSD
dsd2 : BW=60 kHz in DSD
dsd3 : BW=70 kHz in DSD
To select the Headphone Output or Line Out.
VAR : Headphone Output with volume control feature
2V : Fix the output voltage 2V rms
5V : Fix the output voltage 5V rms
The mode will not change if the headphone is plugged in.
You should not connect the Power Amp directly in 2V, or 5V mode.
When to use FLOW with external amplifiers we recommand turning off the charging by CHG-. In some cases the charging noise could be heard.
① USB 2.0/ USB 3.0
Can be used to play music from PCs, notebooks, iOS devices, Android devices, etc.
Can be used to play music from sources with optical outputs.
* You can use the MENU button to change input when both USB and optical connection are connected.
If only one connection is connected, FLOW will use the connection automatically.
The display shows the volume level, audio file data, battery and other information.
On when USB Host is connected
On when optical connection is connected
On when the file played is DSD, it will show also the bit rate of DSD 64 or 128
Battery gauge meter. 5 steps
Shows the bit width of music data 16 or 24. (When used with optic connection only)
When the output level is set to 2V or 5V using the advanced menu
On when the volume knob is changed
Sample Rate display
On when headphone is plugged
On when headphone is unplugged
On when Play
On when Pause
Displays various information such as sampling rate, volume level and the menu mode
Changes according to the volume level
Using the USB Input (PCs and other devices with USB Audio)
The USB A type cable provided with the FLOW should be connected to the USB Audio output of the musical source.
When connected, the FLOW will automatically turn on.
* When using with Windows PC. A software drive installation is needed prior to use. See Driver Installation Section for details.
When only the optical cable is plugged to the FLOW from the music player, FLOW's input mode will be set to Optical automatically.
When both optical and USB connections are maintained, long press the On/Off Power button to access the menu to set the audio input to Optical.
Note: The Optical cable provided with the FLOW has one end with a regular square connector and the other end with a thin 3.5mm connector.
*FYI, the SAMSUNG mSATA is an example of the mSATA drive which is compatible with the FLOW
*Please follow the instructions below when installing a new mSATA SSD.
Remove the 4 screws on the rear panel of the main case.
While holding the top part, let the bottom part softly fall while opening.
After inserting and connecting the mSATA SSD in proper direction, press the clip until the mSATA SSD is secured.
After installing the mSATA SSD, replace the cover and screw in all four screws firmly.
When replacing the cover, take extra care to make sure that the battery cables are not jammed between the top and bottom parts.
After installation of mSATA drive.
1. Make sure the host mode is set to USB2 or USB3 or Mac. It depends on the the Host computer you are using
2. Set the mSATA mode menu to mSAT+
3. Please format the mSATA drive using the format menu of the operating system of your computer. Format menu will differ depending on the PC/Mac's operating system.
The FLOW driver for PCs with Windows OS can be downloaded from the Aurender website at (www.aurender.com).
This USB Audio Driver enables the PCs with Windows OS to be connected to and used with the Aurender FLOW.
Download the drive shown below which is for PCs using Windows OS, and install.
*FLOW uses XMOS chip for USB interface. The driver is provided by XMOS.
- Connect the FLOW to the PC using the USB A Type port.
- Install the driver.
- Go to Computer Management -> Device Manager -> Sound, video and game controllers and you will see XMOS USB Audio as shown below.
Mac does not require installing of drivers
It is strongly recommended that only the provided battery charger be used.
Should another charger type have to be used, the output voltage must be 5V/2A.
Although the time can vary according to various conditions, it usually takes 3-4 hours to charge the battery.
Please note that with all re-chargeable batteries (Li-ion), the length of play time between charges will slowly decrease as time passes.
For fastest charge, please use the AC Adapter enclosed with the FLOW.
Using the USB 2.0 port of PC for charging will be very slow because it can draw only 500mA from the port.
When the mode is iOS or anDR, FLOW will not be charged from the device not to draw current from the phones.
|Product Name||Aurender FLOW|
|USB Interface & controller ||XMOS XS1-U8A-64-FB96|
|USB Audio||USB Audio Class 2.0|
|USB Interface||USB 3.0/2.0|
|Audio Output Termnial||1/4 inch(6.35mm) Headphone Jack|
|Max Audio Output Level||5.1Vrms|
|mSATA Slot||For Optional mSATA storage (User installable)|
|Dynamic Range||Max 122dB|
|Output Power||600 ohm -> 43mW|
300 ohm -> 87mW
56 ohm -> 384mW
32 ohm -> 570mW
8 ohm ->180mW
|Output Impedance||Max 0.06 Ohm|
|THD+N||0.0002% (1kHz 5.1Vrms output)|
|SPDIF Mode(Optic)||Up to 24bit /192kHz sample rate|
|PCM mode(USB)||Up to 32bit/384kHz sample rate|
|DSD Mode (USB)||DSD64, DSD128 / Native DSD through DoP Mode|
|Battery||Samsung Li-ion 4450 mAh|
|AC Adapter for Battery Charging||DC 5V/2A USB A Type|
|Unit Dimension||80 x 137 x 28 (mm)|
|Unit Weight||450g(mSATA excluded)|
|Charging Time||4~5 hours|
|Play Time||7 hours / 300 ohm Headphone|